Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Just about everyone maintains his or her own way of thinking when it comes to How to Install a Bathtub Yourself.
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably hard job. If the old bathtub is readily easily accessible, the task can move rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified yourself for the task and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will aid you set up a new bath tub in your shower room if you have currently purchased a new bathtub and do not need to change the plan of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Planning for the Setup
First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally examine the overflow outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait up until the bath tub has actually been utilized a minimum of when as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can break fairly early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that content about Tools You Need to Install a New Bathtub when doing a search on the internet. Enjoyed reading our content? Please share it. Let others locate it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Get Quote Now Report this page